I have a 2017 xp4 turbo with full aluminum doors. Looking for a good door bag that will work with these doors. Any suggestions?
↧
Door bags
↧
Eibach Stage 3 Install Instructions?
Hey Guys, By chance would someone have a copy of the install instructions/setup for Eibach springs for a XPT4 that they could post or email me? I purchased a set of their stage 3 springs for my 2016 XPT4 and did not get a copy of the install instructions/base setup recommendations. I called Eibach but they are closed until Monday and I would like to get them installed this weekend.
Any help would be appreciated!
Thanks
Casey
Any help would be appreciated!
Thanks
Casey
↧
↧
Popping in the rear end went turning
Guys I adjusted the shocks now I am getting a popping went I turn left or right. It doesnt do it backing up or going forward.
↧
What should I pay for a 2016 turbo 4 seater?
So I am finally ready to purchase a rig for the family. I would love to find a used 17 for the right price. But there just aren't any out there. I am from northeast, outside Philadelphia pa area. There is currently a 16 Rzr 4 turbo pretty close to me at a used motorcycle dealer for $16,999. It has 1400 miles on it. I'm not sure if this is low miles/high?
Not a lot of used turbo out there so I'm really not sure if this price is ok,bad? Should I buy new?..any suggestions out there?
It is currently on eBay now. Crystal white if anyone wants to see condition
Thanks again
Not a lot of used turbo out there so I'm really not sure if this price is ok,bad? Should I buy new?..any suggestions out there?
It is currently on eBay now. Crystal white if anyone wants to see condition
Thanks again
↧
Flop
Hello brand new to forum.but not the side by side or off-road world.had my first flop on passenger side.rolled rzr back over looked like everything was fine till I looked closer noticed windshield was not lining up.had to make slight adjustment for doors to close properly. Am hoping it’s part of the cage like the middle section that is bent, but concerned about possible frame damage is this possible? Input would be greatly appreciated thank you
↧
↧
UTV inc Eleanor
I am considering this cage and would like to see more pictures of it or reviews if anyone has it. I can only find 3 photos of it online and I think all of them are from UTV inc. How much lower is it than the stock cage? I have read that the back seat is not good for those over 5'9" or 5'7" with a helmet, I don't mind this as most of my backseat passengers are not taller than that.
↧
Front diff
I have a 16 turbo 4 and noticing a noise at about 30 mph that sounds like a chain rattling or marbles in a metal can.
Is this the front end noise that is a common complaint?
Already changed the carrier bearing
Is this the front end noise that is a common complaint?
Already changed the carrier bearing
↧
Clutching or something else??
Hey question I just took my paddles off and thru on my 30 Goodyear wrangler pickup tires I run and the clutching does some weird stuff when I let off it sometimes makes grinding sound like Im going between gears in tranny but other times it just slows to a stop really fast? Ive noticed the grinding sound sometimes when I coast down our bigger dunes too but only once in awhile! Any idea just wondering if change something in clutching to fix it! Put stock tires back on to try but still does it some with them on! When I let off it almost like on the brakes hard and then feels like in four wheel drive!
Its on a 18 xpt4 low miles with aa sc3 clutch kit!
Sent from my iPhone using Tapatalk
Its on a 18 xpt4 low miles with aa sc3 clutch kit!
Sent from my iPhone using Tapatalk
↧
Need Help - Question about radiator fan wiring
I finally figured out the issue I was having with overheating on my 2017 XPT 4 . Turned out to be very well hidden dirt in my intercooler and radiator that was still there after several washes. I'll just charge that to stupidity on my part.
It runs well now, but I am adding a reflex fan kit (pusher that goes on the front of the intercooler) just for extra cooling benefit. My problem is that I'm having a hard time finding a good switch wire / source. The kit comes set up to run on it's own rocker. But I want to tie it into my radiator fan, so they both come on and turn off together. There are 4 wires in the factory fan harness; hot, ground, and 2 switch wires (2 stage fan). The problem is that when I try to find a signal in either one of the switch wires when the fan is on, I get nothing. Does anyone know if it's a momentary signal sent to turn the fan on, then another momentary signal sent to turn it off? I was assuming the switch wire would be like most other accessory wires - hot as long as power was needed to that particular system / component. Seems like a simple problem to figure out an overcome, but it kinda stumped me. Any help would be greatly appreciated.
It runs well now, but I am adding a reflex fan kit (pusher that goes on the front of the intercooler) just for extra cooling benefit. My problem is that I'm having a hard time finding a good switch wire / source. The kit comes set up to run on it's own rocker. But I want to tie it into my radiator fan, so they both come on and turn off together. There are 4 wires in the factory fan harness; hot, ground, and 2 switch wires (2 stage fan). The problem is that when I try to find a signal in either one of the switch wires when the fan is on, I get nothing. Does anyone know if it's a momentary signal sent to turn the fan on, then another momentary signal sent to turn it off? I was assuming the switch wire would be like most other accessory wires - hot as long as power was needed to that particular system / component. Seems like a simple problem to figure out an overcome, but it kinda stumped me. Any help would be greatly appreciated.
↧
↧
Sest base lowers, who's is best?
Who has the best seat base lowers? Or are they all pretty much the same. Mostly looking for them just to the the little bit of recline in the seats
↧
Popping in the rear end went turning
Guys I adjusted the shocks now I am getting a popping went I turn left or right. It doesnt do it backing up or going forward.
↧
What should I pay for a 2016 turbo 4 seater?
So I am finally ready to purchase a rig for the family. I would love to find a used 17 for the right price. But there just aren't any out there. I am from northeast, outside Philadelphia pa area. There is currently a 16 Rzr 4 turbo pretty close to me at a used motorcycle dealer for $16,999. It has 1400 miles on it. I'm not sure if this is low miles/high?
Not a lot of used turbo out there so I'm really not sure if this price is ok,bad? Should I buy new?..any suggestions out there?
It is currently on eBay now. Crystal white if anyone wants to see condition
Thanks again
Not a lot of used turbo out there so I'm really not sure if this price is ok,bad? Should I buy new?..any suggestions out there?
It is currently on eBay now. Crystal white if anyone wants to see condition
Thanks again
↧
Flop
Hello brand new to forum.but not the side by side or off-road world.had my first flop on passenger side.rolled rzr back over looked like everything was fine till I looked closer noticed windshield was not lining up.had to make slight adjustment for doors to close properly. Am hoping it’s part of the cage like the middle section that is bent, but concerned about possible frame damage is this possible? Input would be greatly appreciated thank you
↧
↧
UTV inc Eleanor
I am considering this cage and would like to see more pictures of it or reviews if anyone has it. I can only find 3 photos of it online and I think all of them are from UTV inc. How much lower is it than the stock cage? I have read that the back seat is not good for those over 5'9" or 5'7" with a helmet, I don't mind this as most of my backseat passengers are not taller than that.
↧
Front diff
I have a 16 turbo 4 and noticing a noise at about 30 mph that sounds like a chain rattling or marbles in a metal can.
Is this the front end noise that is a common complaint?
Already changed the carrier bearing
Is this the front end noise that is a common complaint?
Already changed the carrier bearing
↧
Clutching or something else??
Hey question I just took my paddles off and thru on my 30 Goodyear wrangler pickup tires I run and the clutching does some weird stuff when I let off it sometimes makes grinding sound like Im going between gears in tranny but other times it just slows to a stop really fast? Ive noticed the grinding sound sometimes when I coast down our bigger dunes too but only once in awhile! Any idea just wondering if change something in clutching to fix it! Put stock tires back on to try but still does it some with them on! When I let off it almost like on the brakes hard and then feels like in four wheel drive!
Its on a 18 xpt4 low miles with aa sc3 clutch kit!
Sent from my iPhone using Tapatalk
Its on a 18 xpt4 low miles with aa sc3 clutch kit!
Sent from my iPhone using Tapatalk
↧
Need Help - Question about radiator fan wiring
I finally figured out the issue I was having with overheating on my 2017 XPT 4 . Turned out to be very well hidden dirt in my intercooler and radiator that was still there after several washes. I'll just charge that to stupidity on my part.
It runs well now, but I am adding a reflex fan kit (pusher that goes on the front of the intercooler) just for extra cooling benefit. My problem is that I'm having a hard time finding a good switch wire / source. The kit comes set up to run on it's own rocker. But I want to tie it into my radiator fan, so they both come on and turn off together. There are 4 wires in the factory fan harness; hot, ground, and 2 switch wires (2 stage fan). The problem is that when I try to find a signal in either one of the switch wires when the fan is on, I get nothing. Does anyone know if it's a momentary signal sent to turn the fan on, then another momentary signal sent to turn it off? I was assuming the switch wire would be like most other accessory wires - hot as long as power was needed to that particular system / component. Seems like a simple problem to figure out and overcome, but it kinda stumped me. Any help would be greatly appreciated.
It runs well now, but I am adding a reflex fan kit (pusher that goes on the front of the intercooler) just for extra cooling benefit. My problem is that I'm having a hard time finding a good switch wire / source. The kit comes set up to run on it's own rocker. But I want to tie it into my radiator fan, so they both come on and turn off together. There are 4 wires in the factory fan harness; hot, ground, and 2 switch wires (2 stage fan). The problem is that when I try to find a signal in either one of the switch wires when the fan is on, I get nothing. Does anyone know if it's a momentary signal sent to turn the fan on, then another momentary signal sent to turn it off? I was assuming the switch wire would be like most other accessory wires - hot as long as power was needed to that particular system / component. Seems like a simple problem to figure out and overcome, but it kinda stumped me. Any help would be greatly appreciated.
↧
↧
Sest base lowers, who's is best?
Who has the best seat base lowers? Or are they all pretty much the same. Mostly looking for them just to the the little bit of recline in the seats
↧
Pulling the trigger 2018 XPT4
Purchasing a 2018 4 seater Turbo this week, anything to look out for? What is everyone paying in the upper Midwest? (MN) I am really nervous trading in 2 machines, but I think its the best for the family as we have a 6 n 8 yr old and both fight over riding in the RZR... I really hate losing the wheeler as I plow with it and I do enjoy all the tighter more technical trails, but more and more of my friends are in the SxS world now and kinda sick of it being up on jack stands for repairs from mudding.. I also hate how much I have into my other machines knowing I am not getting much out of them...
↧
2018 XPT4 Fox Edition Build Thread
I picked up a 2018 XPT4 Fox Edition for some family fun. I always have fun with the build process and plan. For this build my goal is safety, reliability, comfort, and maybe a little more hp in that order. So here is my list so far.
2018 XPT4 Fox Edition Build List
Harnesses
Cage
Belt Fan
Belt Gauge
GPS
Polaris box
Spare tire holder
Fire Extinguisher
15" Wheels
32" Tires
UHMW Skid plate
Long Travel
AA Stage 3 locked and loaded
Probably more that I will need to add along the way.
So here is how it looked on the showroom.
![]()
2018 XPT4 Fox Edition Build List
Harnesses
Cage
Belt Fan
Belt Gauge
GPS
Polaris box
Spare tire holder
Fire Extinguisher
15" Wheels
32" Tires
UHMW Skid plate
Long Travel
AA Stage 3 locked and loaded
Probably more that I will need to add along the way.
So here is how it looked on the showroom.
↧