I replaced my carrier bearing marked my rear driveshaft for reinstal.In the process the mark I made to line rear driveshaft up with rear end got rubbed off. Does this matter? As it looks like it fits in 2 different positions.also as long as long as front driveshaft yoke slides onto front diff and you can get roll pin lined up this shoul be fine right ?the rear driveshaft yoke should slide all the way up onto splines of front driveshaft and this would be correct? Just want to make sure before I button everything up as it has not been a fun experience for a first time Polaris guy hahah. 2017 xpt 4 thanks
↧
Carrier bearing
↧
front harness mount?
I just purchased 4 harnesses for my 2018 RZR XP4 Turbo Fox Edition. the back harnesses mounted up easily, I'm starting to install the front harnesses, do I need to purchase a bar to mount them to? The bar behind the front seats sits to low. any information would be greatly appreciated.
Thank you
First time owner
Thank you
First time owner
↧
↧
17 Turbo XP4 Custom Build Just Finished
Been working on this beast for about the last year, bought new. Think it finally done so figured I would share it with you all. Has way too much to list, there is little left stock. Think my favorite part is both the UTV Wolfpack long travel kit and the full Airdam Clutch setup. Pics below in the next reply.
↧
18 Xp4t walker evans tender springs
I know this has been touched on many times but i wanted to see if anyone has found a cheap solution for the factory useless tenders? I have seen kits for the tenders at all things utv that are on back order. It just seems like you should be able to add any 3 inch inner diameter spring with the correct length and weight and it should work better. I know shock therapy will do a kit for $799 and you can send the entire shock in for revalving. Just asking for experience with only tender replacement.
↧
Belt deflection issue
I have 2018 XPT 4 I bought new a couple months ago. When it was new I tightened the belt deflection up some by adding a thin washer behind the c clip retainer washer and the belt was barley above the secondary clutch and worked well. At 145 miles I blew a belt, my fault we were riding in the mountains in snow and was pushing it hard. I only had my 900 Rzr belt with me for a spare and was good enough to get me through the rest of the day. So when I got home and put a new belt on it it now sits about a 1/4" low and has a harsh engagement and doesn't feel right and has high belt temperatures.
I have had it off too many times to see what is wrong with no luck. I made shims and just used the bolt to try to tighten deflection.
I'm at a loss on what to do I have made several call and no luck.
Any suggestions?
I have had it off too many times to see what is wrong with no luck. I made shims and just used the bolt to try to tighten deflection.
I'm at a loss on what to do I have made several call and no luck.
Any suggestions?
↧
↧
How to make Rzr fit in toy hauler
My XP 4 turbo is too tall to fit in my toy hauler. The opening in my toy hauler is 71 inches high and I need 74 inches of height to fit my Rzr inside. Any ideas of how to drop my Rzrs height a few inches to make it fit in my toy hauler?
↧
Rear axle play at the diff?
How much, if any, play is normal for the rear axle where it goes into the diff? Driver side has none but passenger side will wiggle around a little bit. 2017 XP4 T.
Thanks
Thanks
↧
whos running the Aftermarket Assassins helix?
just trying to get a feel for how this preforms....im running his level 3 tune with his clutch kit and 32" terribites. wondering if i would see better belt temps or get anymore power to the ground.
↧
Sand craft Motorsport complete driveline solution
Okay, we all should know that Polaris RZR's sound and feel like they are about to blow up or break at any point. The whole driveline situation is ridiculous at best. You pay $26-27,000 for a damn toy and they can't give us anything better that this stock setup? It pisses me off that Polaris does this. I had a 2010 4 seater and I figured it was because they were so new. But my 2017 sounds worse. Clanking and grinding!
Anywho... I talked to a few local places that have offered to install the Sandcraft bearing and front diff. upgrade but they said that the driveline is Overkill unless I'm doing some heavy rock crawling or deep mud. Has anyone worked with these? if so How do they like the setup? does it completely fix all the driveline noises we all love so much?
https://sandcraftmotorsports.com/pro...ory/rzr-turbo/
Sent from my SM-G955U using Tapatalk
Anywho... I talked to a few local places that have offered to install the Sandcraft bearing and front diff. upgrade but they said that the driveline is Overkill unless I'm doing some heavy rock crawling or deep mud. Has anyone worked with these? if so How do they like the setup? does it completely fix all the driveline noises we all love so much?
https://sandcraftmotorsports.com/pro...ory/rzr-turbo/
Sent from my SM-G955U using Tapatalk
↧
↧
AA big wheel kit/clutching
I recently purchased mikes big wheel kit from AA, ive spent the last year getting all the supporting mods done and finally got the turbo, most of my riding is at the dunes, i have the performance helix installed. With 30" tires on the level 4 tune i hit 9000 rpms imedeatly on the road, i have only tested it on a service road.
I wanna throw the new paddles on and go test it but i wanna be clear and understand these clutches before i go do that.
It seems to me that range is too high.
It will also peg the rpms on level 3.
Maybe take weights out?
I wanna throw the new paddles on and go test it but i wanna be clear and understand these clutches before i go do that.
It seems to me that range is too high.
It will also peg the rpms on level 3.
Maybe take weights out?
↧
1127 Code - Possible Repair Option
I've got a 2016 XPT-4, stock engine, no tuner and have repeatedly been getting a 1127 Overboost code. I had this code at 30 miles, which the dealer replaced the Waste Gate Control (P/N: 4011285) under warranty.
While riding, last week, in the OR Dunes, the code returned.
I preferred to not spend $140+ for a new control valve and elected to try a different route.
This Control Valve has a atmospheric vent with a vacuum hose extension, which upon removal, I found a fair amount of dirt and sand inside this port. If this port is plugged, the valve will not function properly and set a code.
I bought a small gas engine fuel filter, in an attempt to prevent dirt from entering the valve. So far, so good, granted it's only been a few miles, but it seems to be working well. Perhaps, I've saved myself $140+, maybe not, however $3.95 was a better option worth trying.
While riding, last week, in the OR Dunes, the code returned.
I preferred to not spend $140+ for a new control valve and elected to try a different route.
This Control Valve has a atmospheric vent with a vacuum hose extension, which upon removal, I found a fair amount of dirt and sand inside this port. If this port is plugged, the valve will not function properly and set a code.
I bought a small gas engine fuel filter, in an attempt to prevent dirt from entering the valve. So far, so good, granted it's only been a few miles, but it seems to be working well. Perhaps, I've saved myself $140+, maybe not, however $3.95 was a better option worth trying.
↧
My turn to say lets start the build
Finally I get to say lets start the build. Got the new DIY cage kit from xo fab and doors from utv giants. I already built my front bumper going to build a back bumper. I still need to order the wrap. Not sure what one I want yet. Attachment 555930Attachment 555932Attachment 555934
Sent from my iPhone using RZRForums.net
Sent from my iPhone using RZRForums.net
↧
Secondary clutch
Hey guys... just installed aftermarket assassins snap ring delete kit and notice behind my secondary that I didnt have a splined washer that some people say that have... not sure if there is supposed to be one
Sent from my iPhone using RZRForums.net
Sent from my iPhone using RZRForums.net
↧
↧
Ultimate Crawler Transmission
My '17 XPT4 has been an absolute beast and done everything I've asked of her from Eastern rock crawling to Pritchett Canyon in Moab. However, on a recent trip while crawling up a steep ledge I slipped off backwards while hard on the throttle and the trans exploded when the rear tires landed. Yes yes and yes, failure to control the skinny pedal I know. It literally split the trans from top to bottom. It's still under warranty and will be fixed as such.
Since day one I have been thinking of building the ultimate crawler trans. I think that time has come. So here's the plan:
1) Lightly used donor trans
2) Replace all the OEM bearings with high quality bearings.
3) 12-15% gear reduction
4) Cryo treat & micro-polish the gears
5) Have the syncros cut for L-H shift on the fly (I know a guy ;) )
So a couple of questions:
1) What re the hard core race teams doing to these trans?
2) Anyone making a 300M output shaft for XPT?
3) Polaris list 2 different part #s for the '17XPT4 - Anyone know the difference?
Part# 1333610 (MFG date 8/2/16 - 8/16/16) & 1333744 (MFG pre 8/1/18 post 8/20/16)
Since day one I have been thinking of building the ultimate crawler trans. I think that time has come. So here's the plan:
1) Lightly used donor trans
2) Replace all the OEM bearings with high quality bearings.
3) 12-15% gear reduction
4) Cryo treat & micro-polish the gears
5) Have the syncros cut for L-H shift on the fly (I know a guy ;) )
So a couple of questions:
1) What re the hard core race teams doing to these trans?
2) Anyone making a 300M output shaft for XPT?
3) Polaris list 2 different part #s for the '17XPT4 - Anyone know the difference?
Part# 1333610 (MFG date 8/2/16 - 8/16/16) & 1333744 (MFG pre 8/1/18 post 8/20/16)
↧
Pro armor roof
Anyone with a Pro Armor roof having any issues with creaking sounds. Mine just started and I can’t find what’s causing it. I tried weatherstripping underneath but it didn’t help. Only does it on rocky rails but it’s driving me crazy. Hoping for any idea on the problem and maybe a solution.
↧
Outerwear
Anyone run a outerwear over there air filter? Wondering if it would help or cause a restriction of air flow. Never used outerwear before.
Sent from my iPhone using RZRForums.net
Sent from my iPhone using RZRForums.net
↧
Wastegate setting
Ok so my wastegate rod spun on me because I didn’t tighten the lock bolts enough doing a stage 3 AA tune. How do I accurately find the stock setting for the gate rod? Without guessing
↧
↧
Las Vegas Dealer Show today
Isnt the dealer show in Vegas today? Is anyone reporting announcements?
Sent from my iPhone using RZRForums.net
Sent from my iPhone using RZRForums.net
↧
Dirt engineered doors
Anyone have dirt engineered doors. Are they any good?
↧
2019 LE White Lightening - September Delivery
Owned a 2007 and sold in 2009. Living in Idaho and duning St A. After 10 years of fast sand rails, modified TRX 250Rs, and TRX 450R, adding a new 2019 to my line-up for Idaho Trails/dirt, Utah Moab/Corral Pink, and occasional run at St. A. Excited about the new graphics and patriotic colors!
Who do you recommend for a stylish White Roll Cage upgrade.
Who do you recommend for a stylish White Roll Cage upgrade.
↧